# # $Header: /home/cvs/jakarta-tomcat/src/etc/Attic/workers.properties,v 1.3.2.2 2000/10/16 01:59:22 larryi Exp $ # $Revision: 1.3.2.2 $ # $Date: 2000/10/16 01:59:22 $ # # # workers.properties - # # This file provides jk derived plugins with with the needed information to # connect to the different tomcat workers. # # As a general note, the characters $( and ) are used internally to define # macros. Do not use them in your own configuration!!! # # Whenever you see a set of lines such as: # x=value # y=$(x)\something # # the final value for y will be value\something # # Normaly all you will need to modify is the first properties, i.e. # workers.tomcat_home, workers.java_home and ps. Most of the configuration # is derived from these. # # When you are done updating workers.tomcat_home, workers.java_home and ps # you should have 3 workers configured: # # - An ajp12 worker that connects to localhost:8007 # - An ajp13 worker that connects to localhost:8009 # - A jni inprocess worker. # - A load balancer worker # # However by default the plugins will only use the ajp12 worker. To have # the plugins use other workers you should modify the worker.list property. # # # # workers.tomcat_home should point to the location where you # installed tomcat. This is where you have your conf, webapps and lib # directories. # workers.tomcat_home=/usr/local/tomcat_3.2.1/tomcat-3.2.1 # # workers.java_home should point to your Java installation. Normally # you should have a bin and lib directories beneath it. # workers.java_home=/usr/local/jdk1.3 # # You should configure your environment slash... ps=\ on NT and / on UNIX # and maybe something different elsewhere. # # ps=\ ps=/ # #------ ADVANCED MODE ------------------------------------------------ #--------------------------------------------------------------------- # # #------ DEFAULT worket list ------------------------------------------ #--------------------------------------------------------------------- # # # The workers that your plugins should create and work with # worker.list=ajp12, ajp13 # #------ DEFAULT ajp12 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # # # Defining a worker named ajp12 and of type ajp12 # Note that the name and the type do not have to match. # worker.ajp12.port=4006 worker.ajp12.host=localhost worker.ajp12.type=ajp12 # # Specifies the load balance factor when used with # a load balancing worker. # Note: # ----> lbfactor must be > 0 # ----> Low lbfactor means less work done by the worker. worker.ajp12.lbfactor=1 # #------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # # # Defining a worker named ajp13 and of type ajp13 # Note that the name and the type do not have to match. # worker.ajp13.port=4007 worker.ajp13.host=localhost worker.ajp13.type=ajp13 # # Specifies the load balance factor when used with # a load balancing worker. # Note: # ----> lbfactor must be > 0 # ----> Low lbfactor means less work done by the worker. worker.ajp13.lbfactor=1 # # Specify the size of the open connection cache. #worker.ajp13.cachesize # #------ DEFAULT LOAD BALANCER WORKER DEFINITION ---------------------- #--------------------------------------------------------------------- # # # The loadbalancer (type lb) workers perform wighted round-robin # load balancing with sticky sessions. # Note: # ----> If a worker dies, the load balancer will check its state # once in a while. Until then all work is redirected to peer # workers. worker.loadbalancer.type=lb worker.loadbalancer.balanced_workers=ajp12, ajp13 # #------ DEFAULT JNI WORKER DEFINITION--------------------------------- #--------------------------------------------------------------------- # # # Defining a worker named inprocess and of type jni # Note that the name and the type do not have to match. # #worker.inprocess.type=jni # #------ CLASSPATH DEFINITION ----------------------------------------- #--------------------------------------------------------------------- # # # Additional class path components. # #worker.inprocess.class_path=$(workers.tomcat_home)$(ps)classes # # The XML parser provided with Tomcat # #worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)jaxp.jar #worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)parser.jar # # Tomcat's implementation # #worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)jasper.jar #worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)servlet.jar #worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)webserver.jar # # Javac as available from Java2SE # #worker.inprocess.class_path=$(workers.java_home)$(ps)lib$(ps)tools.jar # # Setting the command line for tomcat # Note: The cmd_line string may not contain spaces. # #worker.inprocess.cmd_line=-config #worker.inprocess.cmd_line=$(workers.tomcat_home)/conf/jni_server.xml #worker.inprocess.cmd_line=-home #worker.inprocess.cmd_line=$(workers.tomcat_home) # # The JVM that we are about to use # # This is for Java2 # #worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)jvm.dll # # And this is for jdk1.1.X # #worker.inprocess.jvm_lib=$(workers.java_home)$(ps)bin$(ps)javai.dll # # # Setting the place for the stdout and stderr of tomcat # #worker.inprocess.stdout=$(workers.tomcat_home)$(ps)inprocess.stdout #worker.inprocess.stderr=$(workers.tomcat_home)$(ps)inprocess.stderr # # Setting the tomcat.home Java property # #worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home) # # Java system properties # # worker.inprocess.sysprops=java.compiler=NONE # worker.inprocess.sysprops=myprop=mypropvalue # # Additional path components. # # worker.inprocess.ld_path=d:$(ps)SQLLIB$(ps)bin #